Nagellan Posted April 25, 2021 Share Posted April 25, 2021 Cześć. Pierwszy raz używam Ispindel także proszę o wyrozumiałość. W Brewfather wyświetla tylko temperaturę i stan baterii. W odzczytach pokazuje temperaturę, stan baterii i kąt wychylenia. Brakuje krzywej obrazującej odfermentowanie. Wcześniej zgodnie z instrukcją zrobiłem kalibrację w 10 punktach pomiarowych i zapisałem Formułę. Poproszę o pomoc. Z góry dziękuje Link to comment Share on other sites More sharing options...
WojtekGaaD Posted April 25, 2021 Share Posted April 25, 2021 Spindel jest skalibrowany? Do pracy solo musisz go skalibrować Link to comment Share on other sites More sharing options...
Nagellan Posted April 25, 2021 Author Share Posted April 25, 2021 Tak. Kalibrowałem w roztworze cukru. Zrobiłem 11 punktów pomiarowych. Zapisałem formułę itd. Link to comment Share on other sites More sharing options...
WojtekGaaD Posted April 25, 2021 Share Posted April 25, 2021 Jak wygląda stan urządzeń? Link to comment Share on other sites More sharing options...
Nagellan Posted April 25, 2021 Author Share Posted April 25, 2021 (edited) U mnie tak to wyglada. Nie wiem dlaczego wyświetla dwa. Choć mam tylko jeden. Edited April 25, 2021 by Nagellan Link to comment Share on other sites More sharing options...
WojtekGaaD Posted April 25, 2021 Share Posted April 25, 2021 (edited) wskazówka z BrewFathera: Make sure your iSpindel reports gravity in Plato (it will be converted to SG) and temperature in Celcius. Add [SG] to the name of your iSpindel if you use SG based formula. If the gravity is displaying 1.004 in Brewfather you are using the wrong formula, use the fomula that reports in Plato or use the tag above. If you get no gravity reported: Check that the formula is not too long. There's a max character length. Instead of "tilt*tilt*tilt" put *tilt^3" etc. If it still fails: Upgrade to the latest iSpindel firmware or try to use the second degree polynomial formula for your iSpindel Edited April 25, 2021 by WojtekGaaD korekta Link to comment Share on other sites More sharing options...
Nagellan Posted April 25, 2021 Author Share Posted April 25, 2021 (edited) Tak tez wpisałem. Użyłem formułe na Plato. Wpisana jest tez krótsza liczba znaków. Firmware mam tez najnowszy. Ale nie próbowałem formuły second degree. Teraz Ispindel pływa w fermentorze w fermentujące brzeczce. Jest jakiś sposób żeby sprawdzić firmware ? Edited April 25, 2021 by Nagellan Link to comment Share on other sites More sharing options...
george1255 Posted April 25, 2021 Share Posted April 25, 2021 Miałem to samo. Nie pokazywało mi gęstość brzeczki. Problem był w błędnej formule. Popraw i niema bata aby nie działało Wysłane z iPhone za pomocą Tapatalk Link to comment Share on other sites More sharing options...
Nagellan Posted April 26, 2021 Author Share Posted April 26, 2021 Dzięki za info. Tez tak podejrzewam że coś nie tak z formułą. Jak skończę fermentacje wrócę do tematu. Pozdrawiam Link to comment Share on other sites More sharing options...
kakaowy Posted April 2, 2024 Share Posted April 2, 2024 Podbijam wątek, urządzenie pokazuje mi ujemne plato XD formuła to "-19.844897959153897 + 1.2543650793626469 *tilt-0.018976757369554217 *tilt^2 + 0.00013463718820815336 *tilt^3" i gdzie jest problem? Link to comment Share on other sites More sharing options...
x1d Posted April 2, 2024 Share Posted April 2, 2024 A jak obliczyłeś formułę? Link to comment Share on other sites More sharing options...
elroy Posted April 2, 2024 Share Posted April 2, 2024 Tak wysoki kąt urządzenia nie powinien wskazywać takiej wartości SG. Co masz w czystej wodzie? Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now